CLICK PHOTO FOR LARGER IMAGES

 

 

ALPHA-NUMERIC TRANSDUCER v3

  BACK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

                                                

 

The ANT v3 is a high-performance instrument which allows up to 8 treatment cards to be used simultaneously. The design does not use electricity or magnetism. The instrument has three main applications:

1. TREATMENT - To provide distant (broadcast) Radionic treatments using various forms of encoded cards, such as:

a) ALPHA-NUMERIC and related cards produced specifically for the ANT instrument;

b) PROGRAMMABLE CARDS, which are pre-charged using the LRI (Large Radionic Instrument);

c) MAGNETO-GEOMETRIC (Rae) cards;

d) standard RADIONIC RATES (printed on a suitably-sized piece of white card);

e) assorted Radionic and Radiesthesic patterns;

f) text written in languages such as English;

g) photographs, X-Rays and symbols, where appropriate.

h) the vibrational characteristics (judged from the Radiesthesic point of view) of any material which can be mounted onto a card and fitted into the card slot. Larger samples may be introduced using the External Well.

2. SYNTHESIS - To enable the practitioner to make remedies printed into water, sac lac or other carriers from the ANT and other cards as described above in 1.

3. COPYING - Copying existing remedies (capturing  the vibrational characteristics). This is typically done using the plug-in External Well (optional extra).

 

FACILITIES

Each card slot has two controls, POTENCY and a POTENCY RANGE SELECTION switch.

1) The POTENCY SELECTION ROTARY CONTROL is calibrated from 0 to 10 and allows potency to be selected over the range 0 to 100MMM. Each number indicates a potency setting. The correlation between number and potency is shown in the table below. Identify the required potency and rotate the control until the calibration mark (graticule) on the knob is aligned with the relevant number on the scale.

KNOB SETTING

STANDARD 'C' POTENCY RANGE

HIGH 'C' POTENCY RANGE

DIRECT (Æ)
POTENCY

0

0

0

Æ

1

6C

6M

Æ

2

12C

12M

Æ

3

30C

30M

Æ

4

100C

100M

Æ

5

200C

200M

Æ

6

1M

10CM

Æ

7

10M

100CM

Æ

8

CM

10MM

Æ

9

MM

10MMM

Æ

10

10MM

100MMM

Æ

Table 1: Knob position vs. Potency correspondence table

3.6) POTENCY RANGE SELECTION SWITCH. Potency range is selected by operating the 4-position click-stop switch. The four positions are denoted OFF, ‘C’ (STANDARD ‘C’), HIGH ‘C’, and DIRECT (Æ).
1. When set of OFF, no signal will pass from the associated card slot to the Output Well.
2. When set to STANDARD ‘C’, the rotary control will provide potencies in the range 0 to 10MM .
3. When set to HIGH ‘C’, the rotary control will provide potencies in the range 0 to 100MMM.

For example, setting 3 will deliver a potency of 30C in the Standard range and 30M in the High range. Positions between the cardinal number points will give an interim potency, e.g. 21C would be found half-way between numbers 2 and 3 in STANDARD ‘C’ range.

4. When set to DIRECT (Æ), the signal will flow from the card slot to the Output Well at full energy but without any potency modification.  DIRECT mode may also be referred to as Null Mode or Null Potency, indicating that there is no change in potency applied.

DIRECT has several applications, such as:
a. Copying or transferring the energy of any substance in the External Well. This will be at 1:1 with regard to the potency of the source material. Thus if you copy an already-prepared homoeopathic remedy at 30C, the copy in the Output Well will be at the same potency. If you copy the energy of a crystal or gemstone, you will copy this energy but without potency. i.e. at Æ.
b. DIRECT may also be appropriate in some treatments and may be indicated by the pendulum when using the Potency Selection Chart in preparing a treatment.

 

OTHER FEATURES

ANT v3 has three connectors.

1) LINK. This is a standard RCA-type phono socket. It allows two ANT v3 instruments to be connected together using a standard phono-to-phone type lead. When interconnected, up to 16 remedy cards can be used together. However, the patient’s witness should only be placed in one of the two available output Wells . More than one witness should NOT be used.

2) PULSE SIGNAL INPUT SOCKET. This is a standard 6.35mm (1/4 inch) stereo jack socket. When being used to give treatments, the ANT v3 requires a pulse signal. This greatly reduces the treatment time. The pulse signal is obtained from an external source, either a CD or .mp3 player (not supplied). 4 pulse tracks are supplied, in both audio and .mp3 formats. These can be loaded onto or replayed from an appropriate external playback device. A lead is supplied with the ANT v3 instrument, this being a jack-to-phono with a phono to mini jack convertor.

3) EXTERNAL WELL INPUT SOCKET. This is a standard 6.35mm (1/4 inch) stereo jack socket. This allows the optional EXTERNAL WELL to be connected to the ANT v3 using a standard jack-to-jack lead (mono or stereo). When a jack plug is inserted, the signal from card slot 5 is cut off and is replaced by the signal from the External Well. The potency range and selection controls associated with card slot 5 can then be used to vary the potency of the signal from the external well. When the jack plug is removed, the signal from card slot 5 is routed back into the potency range and selection controls.

 

For further information, pricing and availability, please contact Nick Franks.

nick.franks@radionics.co.uk