CLICK PHOTO FOR LARGER IMAGE

 

 

ALPHA-NUMERIC TRANSDUCER

'REMEDY MAKER'

 

BACK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

                                                

 

The ANT SCMFP (Single Card, Multi-Function Potentiser), also known as a 'Remedy Maker', is a high-performance instrument which allows synthesis - typically of homoeopathic remedies - from appropriate Radionic codes. The design does not use electricity or magnetism. The instrument has three main applications:

1. SYNTHESIS - allows the user to make remedies printed into water, sac lac or other carriers from Radionic cards and codes, such as:

a) ALPHA-NUMERIC and related cards produced specifically for the ANT instrument;

b) PROGRAMMABLE CARDS, which are pre-charged using the LRI (Large Radionic Instrument);

c) MAGNETO-GEOMETRIC (Rae) cards;

d) standard RADIONIC RATES (printed on a suitably-sized piece of white card);

e) assorted Radionic and Radiesthesic patterns;

f) text written in languages such as English;

g) photographs, X-Rays and symbols, where appropriate.

h) the vibrational characteristics (judged from the Radiesthesic point of view) of any material which can be mounted onto a card and fitted into the card slot. Larger samples may be introduced using the External Well.

2. COPYING - Copying existing remedies (capturing  the vibrational characteristics). This is typically done using the plug-in External Well (optional extra).

3. TREATMENT - To provide distant (broadcast) Radionic treatments.

FACILITIES

The instrument has two controls, POTENCY and a POTENCY RANGE SELECTION switch.

1) The POTENCY SELECTION ROTARY CONTROL is calibrated from 0 to 10. It allows potency to be selected in either C or LM ranges. The C range over is 0 to 100MMM and the LM range is 1 to 9. Each number indicates a potency setting. The correlation between number and potency is shown in the table below. Identify the required potency and rotate the control until the calibration mark (graticule) on the knob is aligned with the relevant number on the scale. The rotary control must be used in conjunction with the Range selection switch (see below).

KNOB SETTING

STANDARD 'C' POTENCY RANGE

HIGH 'C' POTENCY RANGE

LM POTENCY RANGE

DIRECT (Æ)
POTENCY

0

0

0

0

Æ

1

6C

6M

1

Æ

2

12C

12M

2

Æ

3

30C

30M

3

Æ

4

100C

100M

4

Æ

5

200C

200M

5

Æ

6

1M

10CM

6

Æ

7

10M

100CM

7

Æ

8

CM

10MM

8

Æ

9

MM

10MMM

9

Æ

10

10MM

100MMM

OFF

Æ

Table 1: Knob setting vs. Potency correspondence table

2) POTENCY RANGE SELECTION SWITCH. Potency range is selected using the 5-position click-stop switch. The five positions are denoted OFF, ‘C’ (STANDARD ‘C’), HIGH ‘C’, LM, and DIRECT (Æ).
1. When set of OFF, no signal will pass from the associated card slot to the Output Well.
2. When set to STANDARD ‘C’, the rotary control will provide potencies in the range 0 to 10MM .
3. When set to HIGH ‘C’, the rotary control will provide potencies in the range 0 to 100MMM.

4. When set to LM , the rotary control will provide potencies in the range LM 1 - 9

For example, setting 3 will deliver a potency of 30C in the Standard range, 30M in the High range, and LM 3 in the LM range. Positions between the cardinal number points will give an interim potency, e.g. 21C would be found half-way between numbers 2 and 3 in STANDARD ‘C’ range.

5. When set to DIRECT (Æ), the signal will flow from the card slot to the Output Well at full energy but without any potency modification.  DIRECT mode may also be referred to as Null Mode or Null Potency, indicating that there is no change in potency applied.

DIRECT has several applications, such as:
a. Copying or transferring the energy of any substance in the External Well. This will be at 1:1 with regard to the potency of the source material. Thus if you copy an already-prepared homoeopathic remedy at 30C, the copy in the Output Well will be at the same potency. If you copy the energy of a crystal or gemstone, you will copy this energy but without potency. i.e. at Æ.
b. DIRECT may also be appropriate in some treatments and may be indicated by the pendulum when using the Potency Selection Chart in preparing a treatment.

 

OTHER FEATURES

The ANT SCMFP has three connectors.

1) LINK. This is a standard RCA-type phono socket. It allows two ANT instruments - either ANT v3 or ANT SCMFP to be connected together using a standard phono-to-phone type lead. When interconnected, up to 16 remedy cards can be used together. However, the patient’s witness should only be placed in one of the two available output Wells . More than one witness should NOT be used.

2) PULSE SIGNAL INPUT SOCKET. This is a standard 6.35mm (1/4 inch) stereo jack socket. When being used to give treatments, the ANT v3 requires a pulse signal. This greatly reduces the treatment time. The pulse signal is obtained from an external source, either a CD or .mp3 player (not supplied). 4 pulse tracks are supplied, in both audio and .mp3 formats. These can be loaded onto or replayed from an appropriate external playback device. A lead is supplied with the ANT v3 instrument, this being a jack-to-phono with a phono to mini jack convertor.

3) EXTERNAL WELL INPUT SOCKET. This is a standard 6.35mm (1/4 inch) stereo jack socket. This allows the optional EXTERNAL WELL to be connected to the ANT SCMFP using a standard jack-to-jack lead (mono or stereo). When a jack plug is inserted, the signal from the card slot is cut off and is replaced by the signal from the External Well. The potency range and selection controls associated with the card slot can then be used to vary the potency of the signal from the external well. When the jack plug is removed, the signal from card slot is routed back into the potency range and selection controls.

 

For further information, pricing and availability, please contact Nick Franks.

nick.franks@radionics.co.uk